Gm tech2win software serial#

If you have a serial port on the computer, it's probably COM 1 or use the one from the USB adapter.4.īefore you can use Tis2000 with your Tech2, you have to make it 'think' that there is a dongle connected that authorizes it. During the install, it will ask you to specify the COM port.

Gm tech2win software install#

Install the Tis2000 software from the CD included with the Tech2. Go into Device Manager and make note of the COM port used by the adapter.3. If you're using a USB to serial adapter, plug it in now and set it up. I failed to do this at first and caused a lot of headaches later, including a BSOD during software installation.3.

Gm tech2win software drivers#

Installed ALL the required drivers until there were no more yellow check marks in Device Manager. I didn't bother with updating anything else as far as security updates to Windows or install a virus scan because this computer will never be connected to the Internet or used for anything else.2. Installed a fresh copy of Windows XP SP3.

Keep in mind that you should have some computer knowledge and know how to install Windows.1. If anyone gets a virtual install working, please post it up.In some detail, this is what I did. I'm not going to discuss this type of installation but the basic software installation and use will be the same. The challenge of communicating from the virtual environment through the real computer's hardware ports can make it difficult but can be done. VMWare is free to use and it has been done from what I read but could be a fairly involved process because of the serial port issue, especially when using a USB to serial adapter. Laptops that have actual serial ports built in are probably so old that they are too slow or have age and reliability issues.Īnother solution would be to get a USB to serial port adapter and specify the proper COM port number during the install of Tis2000.Another possible solution would be to use a virtual environment on a host computer. In my setup, I used an old IBM T40 laptop, which is fairly decent processor wise, installed a fresh copy of Windows XP SP3 and used a docking station with it that has a serial port. This can be a problem if you only have newer computers.īest and easiest scenario is to use an older laptop computer that has a serial port running windows XP. It will also allow you to reprogram a module that you are replacing.The Tech2 communicates with the computer using a serial port on the computer running Windows XP SP3.

Gm tech2win software update#

For example, I was able to update all of the modules and PCM in my 2006 9-7x even though it had only been a year or two since production and issue of this software. It will have PCM and module updates included. It was discontinued in 2008 by GM which means that it works only for vehicles up to model year 2007. That's because only dealers have those or a clone of one wasn't included.First of all, this is old software. If you install it and try to use it, it says that it can't find the USB security dongle or something like that. If you bought one of the Tech2 clones, it probably came with a CD with the Tis2000 software. Things like updating PCM's and modules and anything security related are locked out. And a lot doesn't apply since it's geared towards Saab (even the 9-7x doesn't apply, it's under GM).So you have a Tech2 but a lot of the things you would like to do is locked out because you don't have access to the computer software to allow you to do it. Press to continue to main menu.A lot of info I found over at but it is just a giant thread to read through although a lot of the info is on the first page. Press to continue.ħ. Now the main VXDIAG GM Tech2Win menu will load. The software will start to load and then show you the main menu. The interfaces available will vary based on other types of diagnostic software you may have installed. In our example, we choose . Based on your region, there will be different models available from the vehicle selection menu.Ī box will pop up asking you to select the manufacturer or interface you’d like to use. This would be based on your region or type of vehicle you’re diagnosing. Then click on .ĥ. Go to the Desktop and start the Tech2Win software from the desktop shortcut icon.Ħ. Right when the software starts, the Tech2Win-Configurator will pop up and ask you to choose which configuration you’d like. This is where you can verify if your hardware is connected, working properly, set which type of connection type you want and more.Ĥ. Go to the tab on the top and go to then . After the installation is complete, go to the Windows Start menu and find the folder and application and open it.ģ. The VX Driver MDI software allows you to manage the interfaces currently connected to the PC.

Then open the folder and open the to install the software.Ģ. Setup Tech2win on Windows 10 step-by-step:ġ. Insert Disc or open the downloaded software folder.